o ring design calculator

Home o ring design calculator

images

Parker O-Ring Selector / Calculator

Parker O-Ring Selector / Calculator. Parker`s O-Ring Selector. is an engineering tool which offers O-ring material and size selection combined in one tool. Both are interlinked, thus ensuring the best possible combination of the calculated O-ring size and material choice. The O-Ring Selector covers both imperial and metric standards.

O-ring Groove Calculator | O-ring

The O-ring groove calculator enables engineers to specify an O-ring groove for any given O-ring or vice versa calculates the best suitable size O-ring for any given groove. The calculator takes all relevant parameters into account like: O-Ring squeeze. Free groove volume. O-Ring inner diameter stretch, outer diameter squeeze.

DESIGN ENGINEERS' O-RING SIZE GUIDE - Pressure Seal

DESIGN DIMENSIONS FOR O-RING INSTALLATION O-rings are normally used as seals in several ways, and dimensions of the groove or gland will also vary with the cross section of the ring, the type of operation, and the amount of pressure used in the system. These dimensions will also be different if the O-ring is sealing a liquid which has a low volume

Parker O-Ring Calculator

Mobile inPHorm O-ring Calculator . Take the guesswork out of seal design and material selection with our Mobile inPHorm O-ring Calculator. Utilize our software to guide you through the design and selection of an O-ring and corresponding seal gland. Parker's calculator not only addresses standard O-ring sizes, but allows the you to custom design O-ring glands and seals specifically for your ...

O-Ring Calculator | Ceetak Sealing Solutions

The O-ring calculator tool is intended to form the basis of an o-ring installation, and assist with selection of o-ring and hardware dimensions. Recommendations are based on available technical information, and are offered as suggestions only, any reliance placed on such information by …

O-Ring Calculator | Trelleborg Sealing Solutions

Our online O-Ring calculator offers a quick and easy way to calculate O-Ring dimensions and the appropriate housing layout in accordance with the international O-Ring standard ISO 3601. It also recommends O-Ring sizes, housing layout and part numbers.

O-Ring Groove Design | Global O-Ring and Seal

The gland retaining the o-ring has a rectangular area. Once the o-ring cross-section is selected and the gland height is calculated (to achieve the desired squeeze to the o-ring), the final calculation will be the gland width. To find the minimum area necessary, calculate the total volume of the o-ring which creates the rectangle to hold that ...

Mobile inPHorm - Parker's Design Tool & O-Ring Calculator

2. Find the recommended O-ring size and gland dimensions in the appropriate design table in Static O-Ring Sealing or Dynamic O-Ring Sealing, Sections IV and V, respectively. 3. For industrial use, order the O-ring by the Parker compound number followed by the size number. Example: N0674-70 2-325. 4.

O-Ring Groove Dimensions Calculator | Precision Polymer ...

O-ring Groove Design in 3 easy steps: Step 1. Choose whether you are working with existing hardware or designing new hardware. Select the type of O-ring groove - piston, rod, face seal or trapped seal. If the O-ring size required is known, simply select the AS, BS or ISO standard (such as AS568) and enter the dash size reference.

ERIKS O-Ring Calculator

ERIKS standard O-Rings. and load them also into your created design. info. chemical volume swell (%) cross section diameter (mm) ISO 3601. free. Calculate Results. Reset calculator.

eFunda: Radial O-Ring Selector

Calculator Introduction. This calculator allows you to find the recommended O-Ring inner diameter and range of cross section diameters that will fit a given gland size and tolerance range in a radial seal. Inputs. Bore diameter, Bd: mm cm in. Bore Tolerance, Btol: mm cm in. Groove Diameter, Gd: mm cm in.

O-Ring Calculator: Tech Support - Max Spare Limited

Pressure- Upto 100 Bar-O-Ring-75° Shore A Hardness. Pressure- Upto 150 Bar-O-Ring-90° Shore A Hardness. Pressure- Above 150 Bar-Recommend to use Backup Ring.

Parker O-Ring Selector / Calculator

Parker´s O-Ring Selector is an engineering tool which offers O-ring material and size selection combined in one tool. Both are interlinked, thus ensuring the best possible combination of the calculated O-ring size and material choice. The O-Ring Selector covers both imperial and metric standards.

O-Ring Calculator | Trelleborg Sealing Solutions

O-Ring Calculator. The online O-Ring Calculator offers engineers and professionals a quick and easy way to calculate O-Ring dimensions and the appropriate housing layout in accordance with the international O-Ring standard ISO 3601. By simply entering installation specifications for an application, it recommends O-Ring sizes, housing layout and ...

O-Ring Calculator | Rubber Technology

The ERIKS O-Ring design calculator features the calculation of: for axial seals with inner or outer pressure, piston seals and rod seal applications. Worldwide unique online calculation tool taking into consideration of the thermal expansion of the construction parts and the O-Ring. As well as the chemical volume swell or shrinkage of the O-Ring.